Updated November 2026
Learning how to change tires on ATV models takes an afternoon and a few basic tools. You will remove the wheel, break the bead, get the tire off the rim, and mount and seat the new one. Done carefully, the job is safe to do in your garage or at a trailhead with a spare.
What You Need Before You Start
Gather everything first so you are not stopping halfway through with a wheel in the air. Most owners work with the following:
Shopping for one? See our guide: 7 Best Atv Quad Tires for Sale: Our Picks for Every Trail.
- A floor jack or ATV lift and jack stands rated for the machine’s weight
- Socket set, impact wrench or breaker bar, and the correct wheel nut size from your owner’s manual
- Tire irons (plastic or nylon tipped to protect the rim), rubber mallet, and bead lubricant or soapy water
- A bead breaker tool, or a method for pushing the bead off the rim
- Air compressor or inflator with a gauge, and a tire pressure gauge
- Replacement valve stem, and a tube if your rims use one
Step-by-Step: Removing the Old Tire
- Lift and support the machine. Place the ATV on level ground, engage the parking brake, and support the frame on jack stands. Never work under a machine held up by the jack alone.
- Loosen the wheel nuts while the tire is still on the ground. Break them loose, then raise the wheel and remove the nuts.
- Deflate the tire completely. Remove the valve core so air exits fast. Leaving any pressure in the tire is a common cause of injury.
- Break both beads. Press the sidewall away from the rim on both sides. A bead breaker makes this quick and safe. Without one, a second person can stomp the tire near the rim while you pry with a tire iron.
- Work the tire off the rim. Lubricate the bead, then use two tire irons spaced a few inches apart. Keep the tips away from the valve stem and rim edge, and go slowly around the wheel.
Mounting and Seating the New Tire
Fitting the new tire goes in reverse, but seating the bead is where most problems happen. Check the tire’s rotation arrow and match it to the direction of travel.
- Lubricate both beads and the rim edges. Use a bead lubricant made for tires, or soapy water. Dry rubber grips the rim and makes seating harder.
- Mount one bead, then the other. Start at the valve stem so the stem sits in its hole. Work the tire on with your hands and mallet, keeping the tire centered.
- Inflate to seat the beads. Use a compressor with a gauge. Bead seating often needs a quick burst of air, and you will hear the beads pop into place. Stop at the seating pressure your manufacturer lists, and do not exceed it.
- Adjust to operating pressure. Set the pressure you normally run for your terrain. Check it again after a few miles, since the tire can settle.
Reinstalling the Wheel
Put the wheel back on, then tighten the nuts in a star pattern, not around the circle. Torque them to the specification in your owner’s manual. Lower the ATV, then check torque once more after the first ride, because nuts can loosen as the tire seats.
Common Mistakes
- Inflating past the seating pressure to force a bead, which can cause the tire to burst.
- Using metal tools that gouge the rim and create a leak path.
- Skipping lubricant, which tears the bead and damages the tire.
- Installing a tire backward relative to its rotation arrow.
- Forgetting to recheck wheel nut torque after the first ride.
Recommended Gear
- Plastic tire irons: Their tips reduce rim damage during removal and mounting. View on Amazon
- Bead breaker tool: Separates the tire from the rim without the risks of stomping. View on Amazon
- Digital tire inflator with gauge: Makes accurate bead seating and pressure setting easier. View on Amazon
For more on sizing and pressure, see How to Replace ATV Tires: A Step-by-Step Guide for Beginners and Tire Pressure for ATV Tires: How to Set the Right PSI for Trail and Mud. If you are unsure about fit, ATV Tires Size Chart: How to Read Sizes and Pick the Right Fit explains the numbers. Bead seating can be tricky, so Bead Breaker for ATV Tires: How to Seat and Break Beads Safely covers that step in more detail.
FAQ
Can I change an ATV tire without a bead breaker?
Yes, but it takes more effort and carries more risk. Lubricate the bead well, use plastic tire irons, and have a helper if possible. A bead breaker is safer and faster.
How do I know if my ATV has tubes?
Check the owner’s manual or look at the tire and rim labeling. Many ATV tires are tubeless, but some rims and older tires still use a tube.
Why won’t my tire seat on the rim?
The bead is usually dry, dirty, or not centered. Clean and lubricate the bead, center the tire, and add air in short bursts without exceeding the manufacturer’s maximum seating pressure. If it still will not seat, stop and take it to a shop.
Conclusion
Changing an ATV tire comes down to careful preparation, a clean and lubricated bead, and patient seating at the correct pressure. Follow the manufacturer’s torque and pressure specs, and recheck your wheel nuts after the first ride. For any step you are unsure about, consult a qualified service technician.
