Updated November 2026

Handguards for dirt bike riding shield your hands from brush, branches, flying debris and the occasional tree limb that reaches across the trail. This guide walks you through choosing the right style for your riding, checking fit on your bars and hoses, and mounting them so they stay put on rough ground. Most riders can finish the install in under an hour with basic hand tools.

Choose the Right Style for How You Ride

Handguards come in two main designs. Full-coverage shields wrap around the lever and the bar end, which gives the most protection in dense woods or motocross tracks with tight rhythm sections. Shorter deflector-style guards cover less area, keep weight down and suit open trails where you mostly need protection from wind and light brush. Plastic guards flex on impact and are common on both trail and track bikes, while aluminum options are stiffer and tend to suit riders who want a more rigid mount. Check whether the guard is designed for your bike’s bar diameter, usually 7/8 inch or 22 mm, and whether it works with your handlebar clamp style.

Shopping for one? See our guide: Rzr Electric Dirt Bike (2026): Which Should You Choose?.

Check Clearance Before You Mount

Before you buy, confirm that the guard will not hit your throttle, clutch or brake lever at full lock. Turn the bars fully left and right with the bike on a stand and watch for contact. Also check that the guard will not rub the fuel tank, airbox cover or front brake hose when the forks compress. Some riders run aftermarket levers or hot-start levers, and these can change clearance, so measure again if you have made changes.

How to Mount Handguards on a Dirt Bike

Most kits use a clamp or bracket that bolts to the bar near the controls. Work through the steps below in order.

  1. Remove the throttle tube and clutch lever if the kit requires it, and note how the cables are routed.
  2. Position the mounting bracket on the bar where the manufacturer’s instructions indicate, typically a set distance from the grip or clamp.
  3. Tighten the bolts gradually, alternating sides, until the guard is snug but still adjustable.
  4. Turn the bars through full lock and confirm the guard clears the controls, hoses and tank.
  5. Torque the bolts to the value listed in your owner’s manual or the kit instructions, then recheck after your first ride.

Use threadlocker on the mounting bolts if the instructions recommend it, and check the bolts again after the first few rides, since vibration loosens fasteners over time.

Maintenance and Replacement Tips

Inspect handguards after every few rides. Look for cracks at mounting points, loose bolts, and plastic that has gone brittle from sun exposure. A guard that has taken a hard hit may have stress fractures you cannot see at a glance, so replace it rather than trusting a repair. Keep spare mounting hardware in your toolkit, since trail vibration can shake a bolt loose mid-ride.

Common mistakes to avoid

  • Mounting the guard without checking full-lock clearance against the throttle and levers.
  • Overtightening bolts on plastic guards, which can crack the mounting points.
  • Skipping the recheck after the first ride, when bolts often settle.
  • Choosing a guard for the wrong bar diameter, leading to a loose or unsafe fit.
  • Ignoring small cracks, which can grow and fail when you need protection most.

A basic set of metric hex keys and a torque wrench helps you mount the guard to the manufacturer’s specs. Threadlocker is useful for keeping mounting bolts from backing out on rough trails, so look for a medium-strength formula. Spare mounting hardware is worth keeping in a trail kit in case a bolt is lost or damaged.

  • A torque wrench lets you tighten bracket bolts to the specified value rather than guessing. View on Amazon
  • Medium-strength threadlocker keeps vibrating bolts secure without making future removal difficult. View on Amazon
  • A metric hex key set covers the bolt sizes common on most dirt bike hardware. View on Amazon

FAQ

Do handguards fit every dirt bike?

No. Handguards are sold for specific bar diameters and control layouts, so check the kit’s compatibility list against your bike’s model year. Aftermarket levers and hand controls can also affect fit.

Are plastic or aluminum handguards better?

Plastic flexes on impact and is common on trail bikes, while aluminum is stiffer and often chosen for a more rigid mount. Either can work well if it fits your bars and riding style.

How often should I check handguard mounting bolts?

Check them after the first ride, then at regular intervals, especially after rough trail sessions. Vibration can loosen bolts over time, so a quick check before each ride is a good habit.

Conclusion

Good handguards protect your hands without getting in the way of your controls. Match the style to your terrain, confirm full-lock clearance, and mount the guard carefully with the torque specs from the manufacturer. Recheck the hardware often, and replace any guard that shows cracks.

Lauren Holland

About Lauren Holland

Lauren Holland is part of our editorial team and reviews and edits our ATV, UTV/side-by-side & dirt bikes guides, checking product details against manufacturer specifications and owner feedback.