Updated November 2026

ATV gun rack mounts hold a rifle or shotgun securely on your machine so it stays put over rough trails and does not swing into the handlebars or your leg. This guide walks you through picking the right mount type, checking fit on your ATV, and installing it so it stays solid under load. Read your local laws on transporting firearms before you ride with one.

Step 1: Pick the Right Mount Type

Most mounts fall into three groups. Rack-style mounts clamp to the front or rear rack tubes and suit long guns with a sling or a wide stock. Bar-style mounts attach to the handlebar or a front bumper and keep the muzzle pointed forward. Frame-style mounts bolt to the chassis or a rear cargo rack and work well for riders who carry a rifle every trip.

Shopping for one? See our guide: 5 Best ATV Tires Tire Racks for Garage Storage (2026).

Look for a mount that holds the gun by the stock or barrel with padded contact points, not by a single thin strap. Check that the rubber or foam pads are thick enough to protect the finish.

Step 2: Check Fit Before You Buy

Measure the diameter of your rack tubes or bar before you order. Mounts are usually sold for a specific tube size, and a mismatch means slop or no fit at all. Also measure the width of your longest firearm’s stock and the barrel diameter at the clamp point. Compare those numbers to the product’s stated range.

Confirm the mount does not block your headlight, throttle cable, brake lines or the rider’s leg room. Sit on the ATV in your riding position and move the gun into place to see what it touches.

Step 3: Install the Mount Securely

Use the hardware the manufacturer supplies and torque each bolt to the value listed in the instructions. Loose bolts are the most common cause of a mount failing on the trail. Add thread locker to bolts that thread into metal, and recheck them after your first 10 to 15 miles.

Place the gun so the muzzle points forward or to the side, never toward a rider or passenger. Set the mount so the firearm sits at a height that lets you dismount without catching the stock on your leg.

  1. Gather the mount, bolts, washers, lock washers, thread locker and a torque wrench.
  2. Test-fit the mount on the tube or bar and mark the bolt holes.
  3. Install the mount loosely, then position the firearm and adjust the angle.
  4. Tighten bolts in a crisscross pattern to the specified torque.
  5. Load the rifle, give the mount a firm shake in each direction, and recheck the bolts.

Step 4: Test the Setup on Real Terrain

Ride a short loop over ruts, washboard and small jumps before a longer trip. Watch for rattling, shifting or contact with cables and bodywork. A mount that moves in a test run will move more on a real trail.

Recheck every fastener after the first ride and again after any trip with heavy mud or water crossings, since grit can loosen clamps over time.

Common Mistakes to Avoid

  • Mounting a rifle with the muzzle pointed toward the rider or a passenger.
  • Skipping the torque spec and tightening bolts by feel alone.
  • Using a mount rated for a smaller tube or thinner stock.
  • Letting the firearm sit over the exhaust or engine, where heat can damage the stock.
  • Riding with an unsecured gun because the mount looks solid when parked.

A padded universal gun rack for ATV handlebars or racks gives you a secure hold without custom fabrication. View on Amazon

Blue threadlocker for ATV and UTV bolts helps keep fasteners from backing out on rough trails. View on Amazon

A torque wrench sized for ATV hardware lets you hit the manufacturer’s spec on every bolt. View on Amazon

FAQ

Can I mount a rifle on any ATV?

Most ATVs with front or rear racks can take a mount, but you need to match the mount to your rack tube size and confirm clearance with the controls and bodywork. Check the mount’s stated fit range before buying.

Is a gun rack mount safe for trail riding?

A properly torqued mount with padded contact points holds up well on most trails. Recheck the bolts often, and consult the mount maker and a qualified dealer if you plan to carry heavy firearms over steep or rough terrain.

Do I need to unload the firearm before mounting it?

Yes. Unload and secure the firearm, and store ammunition separately, before installing or removing a mount. Follow your state’s transport rules, which may require a case or specific storage while riding.

Conclusion

Choosing the right ATV gun rack mounts comes down to matching the mount type and tube size to your machine, then installing it with torqued hardware. Test the setup on a short ride and recheck the bolts after every trip. A secure mount keeps your gun steady and your ride safer.

Graham Fisher

About Graham Fisher

Graham Fisher is part of our editorial team and reviews and edits our ATV, UTV/side-by-side & dirt bikes guides, checking product details against manufacturer specifications and owner feedback.